Sobre uma fundação elástica Winkler, encontra-se uma viga em consola com uma secção retangular que está sujeita a uma carga distribuída. The image shows the calculation of the maximum deflection and maximum bending moment.
A viga de aço de secção quadrada está sujeita a uma força normal e a uma carga distribuída. The image shows the calculation of the maximum bending deflection and critical load factor according to the second-order analysis.
A viga de aço carregada axialmente com uma secção quadrada está apoiada sobre uma articulação numa das extremidades e sobre uma mola na outra extremidade. Two cases with different spring stiffnesses are considered. The verification example solves the calculation of the load factors of the beam in the image using the linear stability analysis.
Uma viga em consola com fibras que não correm na direção do eixo da viga de uma secção quadrada sob pressão de tração. Calculate the maximum deflection.
Quatro pilares estão fixados na parte inferior e ligados por um bloco rígido na parte superior. The block is loaded by pressure and modeled by an elastic material with a high modulus of elasticity. The outer columns are modeled by linear elastic material and the inner columns by a stress-strain diagram with decaying dependence. Assuming only the small deformation theory and neglecting the structure's self-weight, determine its maximum deflection.
Uma viga de secção variável em consola está completamente fixada na extremidade esquerda e carregada por uma carga contínua. Plastic material is considered for the calculation.
Um cabo de aço ou uma membrana com pinos nas duas extremidades é carregado por uma carga distribuída. Neglecting its self-weight, determine the maximum deflection of the structure using the large deformation analysis.
A vertical cantilever with a square cross-section is loaded at the top by tensile pressure. A consola é feita de um material isotrópico. Calculate the deflection.
O modelo da estrutura é constituído por duas vigas de treliça que estão incorporadas nos apoios de articulação. The structure is loaded by concentrated force. The self-weight is neglected. Determine the relationship between the loading force and the deflection, considering large deformations.
A structure made of I-profile trusses is supported on both ends by spring sliding supports and loaded by transversal forces. O peso próprio não é considerado neste exemplo. Determine the deflection of the structure, the bending moment, the normal force in the given test points, and the horizontal deflection of the spring supports.
É definida uma viga em consola com uma secção de viga em I de comprimento L. The beam has five mass points with masses m acting in the X-direction. The self-weight is neglected. The frequencies, mode shapes, and equivalent loads of this 5-DOF system are analytically calculated and compared with the results from RSTAB and RFEM.
Sobre uma fundação elástica Pasternak, encontra-se uma viga em consola com uma secção retangular que está sujeita a uma carga distribuída. The image shows the calculation of the maximum deflection and maximum bending moment.
Uma alvenaria está sujeita a uma carga distribuída a meio da secção superior. The Isotropic Masonry 2D material model is compared with the Isotropic Linear Elastic model, with surface stiffness property Without Tension in the nonlinear calculation.
O modelo da estrutura é constituído por duas treliças de comprimento desigual que estão incorporadas nos apoios de articulação. The structure is loaded by concentrated force. The self-weight is neglected. Determine the relationship between the loading force and the deflection, considering large deformations.
A structure made of an I-profile is fully fixed on the left end and embedded into the sliding support on the right end. A estrutura é constituída por dois segmentos. The self-weight is neglected in this example. Determine the maximum deflection of the structure, the bending moment on the fixed end, the rotation of segment 2, and the reaction force at point B by means of the geometrically linear analysis and the second-order analysis. The verification example is based on the example introduced by Gensichen and Lumpe.
Imaginemos um tubo de andaime resistente à flexão fixado por um apoio nodal para andaimes na parte inferior e carregado por um momento e por uma força. Calculate the maximum deflection with consideration of initial slippage.
Imaginemos um tubo de andaime resistente à flexão fixado por um apoio nodal para andaimes na parte inferior e carregado por um momento e por uma força. Calculate the maximum radial deflection by exceeding the capacity of the scaffolding support.
Análise de histórico de tempo na viga em consola (sistema SDOF) excitada por uma função periódica. Vertical deformations and accelerations calculated with direct integration and modal analysis in RF‑/DYNAM Pro - Forced Vibrations are compared with the analytical solution.
Este exemplo serve para ilustrar o plano. The application is shown on a two-story structure. The structure is loaded by means of lateral forces according to Figure 1. Determine the maximum deflection of the structure ux in the direction of the loading forces using both the diaphragm constraint and the plate model of the floor.